Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, I have a CUCM 12.5 system where a Call Pickup Group is not working as it should. I have checked the CSS and Partition setup and all phones are assigned CSS's which have access to the Partition containing the pickup number. However when I use Dial...
Hello, Cisco Support Community Group,Good morning or good evening,I hope all is well.I have a router model 2811 with 4 ports, and I'm using one of them, port 0/1/0, for a Primacell FWT However, the number appears as "unknown.".Also, I have another r...
I am hitting an unusual issue with password resets on Cisco Unity Connection. 8.6We have a list of folks who perform the routine password resets that are often required of end users.I am seeing an issue that is intermittant (I love that word), I know...
We have a cluster of 6 Sub+ 1 Pub. Encountering 404 not found with Digit analysis failing in 3 nodes which are in DR site but calls are routing successfully in DC nodes. Adding to this, Dialed Number Analyzer gives "Block this pattern" in DR site nod...
Could someone tell me where is the best place to globalise the called party from the perspective of a phone please?I am migrating to E164 and would like to know if this could be done at the device pool level using transformation patterns.e.g. If a us...
HiWe are trying to deploy a new Cisco 840 Wireless phone in our site.Anyone can you give me the steps for connecting the Cisco 840 phone and getting registered with the Call manager?regardsChandru
I have strange issue on CUCM. SIP Trunk has been setup for ISTP, outgoing calls work. But CUCM send 404 not found to SBC. SBC is not under my control.Receving called number is full range starts with +994XXXXXXXXX ( "X" are numbers).I have setup Trans...
i have CP-8841 that i changed firmware to CP-8841-3PCC sip88xx.12-0-4MPP0101-205.loads with TFTP and now just show Enter activation code on phone.from https://192.168.199.102/admin/advanced i feel sip settings for my elastix but no any registration l...
Good Morning, So, we set up our CUCM and a majority of our phones have already registered with the numbers and names assigned to them, but there are a couple that are asking for an activation code or domain. None of the rest of them asked for it, but...
What is the license required to order Cisco CME running on an 8300 router and has 20 phones 7821, and 8841?
I'm attempting to modify the diversion header when calling one specific number. I want to modify the reason=unconditional to reason=deflection. I've made a single peer that I confirmed is matched, and assigned a sip profile to the outgoing peer whi...
HI, we have project requirement to integrate the Iridium Satellite phone integration with Cisco PABX to make a calls in case of emergency. Can you please suggest, what can we achieved with this interface.1) can we make calls on any number at cisco PA...
Hi all,I'm facing an issue with my SPA 8800 (Firmware: 6.1.11(XU)) configuration in Mexico. I'm attempting to utilize one FXO port and direct all calls to a SIP trunk.Here's my Dial Plan 8: (<:2010@192.168.5.2>S0)The ATA is located in Mexico, connect...
Hi,I am getting the CDR error like below 10021 There are no matching recordsVerified under service parameters , cdr flag enabled True Please helpCUCM 11.5 Thanks
Hi, When a call is made to 8.XXX.XXXX x1145 from a video phone on the A end in this case an cisco 8865 with x2222. The call establishes with auto attendant on the B end and then presented to the end user at x1145. The B end user picks up the call and...
