02-27-2016 02:02 PM
HI,
I am in very great dilemma.I have 1 Gbps link from my service provider.I am running BGP to establish the connectivity with service provider PE.
Just to brief you , I have redundant links on 2 -Cisco 3750 ( Primary link & secondary )connecting to service provider side and there are 4 routers for 2 services ( Primary and secondary each for 2 services)now the utilization on applications of services -1 has increases and reaches 900~950 Mbps,not to impact services-2 ,I 've driven the traffic of services-2 through secondary link.I have attached ppt for some undestanding
Till few weeks back the utilization was around 750 Mbps in input direction and 700 Mbps in output direction of WAN port on service 1 routers but now the input utilization has started reaching 900~950 Mbps in input direction.
I have 7600-SIP 400 ( sub slot- 5XGE-SPA) on routers [For Qos services ] with are connected to switches.I have discussion with service provider and they said that They would provide be one more think and so that I thought of doing first 2- ports aggregation between Service provider device & 3750 switch and another 2-port aggregation between 3750 switch & services -1 (Cisco7606) router.
There is no issue to create ports aggregation betn Service provider device & 3750 switch.It's not happening between 3750 switch & services -1 (Cisco7606) router because as per Cisco document port aggregation is not supported on 7600-SIP 400.
It takes time for service provider to provide 10 gig port .I have WS-X6548-GE-TX module on services -1 (Cisco7606) router.So I thought connecting router WS-X6548-GE-TX ports of router with switch and create port channel between Them.But I am wondering how would QOS feature can be used.
So I need an advice whether WS-X6548-GE-TX ports support QOS with Etherchannel.
Your advice will be appreciated
R's
Bibek
Solved! Go to Solution.
02-29-2016 10:46 AM
The 3750 is a layer 3 switch. Could you change the design to allow layer 3 links through to it?
What about getting a 10Gbe module for the 3750 and your 7600(s)?
02-28-2016 06:25 PM
The release notes for 12.2(17b)SXA seem to indicate Etherchannel support.
Support for more than 1 Gbps of traffic per EtherChannel on the WS-X6548-GE-TX and WS-X6548V-GE-TX switching modules
02-29-2016 01:23 AM
Hi Philip ,
WS-X6548-GE-TX supports Ether channel but my concern is how can I use this module for Qos feature.
R's
Bibek
02-28-2016 06:26 PM
Why not just create two layer 3 connections between the 7600 and the 3750's and let BGP load balance?
02-29-2016 01:29 AM
02-29-2016 10:46 AM
The 3750 is a layer 3 switch. Could you change the design to allow layer 3 links through to it?
What about getting a 10Gbe module for the 3750 and your 7600(s)?
03-08-2016 02:16 AM
HI,
Changing design is not possible .I am going to get 10Gig port.
Right now I have 7600-SIP-400 on 7600 ( with 4 slots) and going to get SPA-1X10GE-L-V2 ( this will be mounted in 7600-SIP-400 )
Can you tell me if I can use one SPA-1X10GE-L-V2 in one slot and one 5xGE SPA in another slot.
SPA-1X10GE-L-V2 some with module with single 10 Gig port and 5xGE SPA comes with 5 one-gig port
R's Bibek
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide