Hi, I am planning to migrate some 1832i AP 8.5.171 to 9800 17.12.2, can we point the AP to the new WLC, will it upgrade itself? Is any code conversion required prior?Both are in HA and ISE with Mac authentication for clients, what's the preferred wa...
Forum Posts
Hello Folks,We are observing a strange issue where cisco C9120AXI-E disconnects from wlc 9800L which is in GCP intermittently through out the day.We have a cisco sdwan overlay which connect GCP vedge to remote site vedge via ipsec tunnels C9800-CL...
Hello, I have Cisco Mobility Express 1830 AIR-AP1832I-E-K9, with additional 9 same model APs and one little different AIR-AP1832I-I-K9.We are having issue about 5Ghz network, on AIR-AP1832I-E-K9 model access points, clients only connect to 2.4Ghz net...
Hi, I bought one ws-svc-wlan-k9 module. But the seller did not clear the settings. and I don't have access to CLI. I found a description of how to clean it, but I can't find anywhere to download these images.c6svc-wlan-k9w7.passwd.recovery.1.1.1.bin ...
I am trying to start on my Wireless studies and have an NM-AIR-WLC6 in a 2851 router. I have spent a lot of time trying to get 2 different 1240s and a 3502 APs to connect to it. I have reached a point where one is trying to connect and it says the...
I have just replaced an AP with a newer AP and the new AP is online and working but I have no clue how to remove the old ap from the WLC and it just shows as not joined. Any help would be grateful!This is what we see
Hi everyone,Happened to view some logs from our core switch like:Jan 2 02:27:44.265: SW1: IP: recv fragment from 10.80.36.33 offset 0 bytesJan 2 02:27:44.265: SW1: IP: recv fragment from 10.80.36.33 offset 1480 bytesJan 2 02:30:01.655: SW1: IP: recv ...
Resolved! WAPs with EWCs
Hello - I have a wireless environment that has 4 -1600 series aironet waps that need to be replaced. I see the 9100 catalyst series offer EWC on the access points themselves. If I replaced these 4 would I need each of the new access points to have ...
Resolved! AP 2802i from ME to Lightweight
Hi,I need to convert AP type 2802i from Mobility Express back to lightweight.So far have done hard reset, and when it boots it restarts config wizard for ME. How can I remove ME and make it join WLC againt ?thanks for help !
Hi Guys,Currently I am doing a wireless review. Some of the aspects being reviewed are AP tx power and clients connected to the AP on each radio. I am able to get the tx power on each radio by issuing "show advanced 802.11a/b txpower" command. But I ...
Hi everyone,I currently have 3 x model AIR-AP1832I-K9 running CAPWAP with WLC2504, due to WLC2504 failure I have switched 1 AP1832I to Mobility Express Firmware 8-10-185 mode.After I completed the transfer, the AP rebooted continuously and did not bo...
I have several AP's that all connect to a WLC just fine. There are some AP's that have lots of clients though. Most of my APs have 3 to 9 clients which shouldn't be too bad. One of the APs has 23 clients on it, however. How do I configure load balanc...
Hey,I tried to create a new virtual interface on WLC 3051 but when I click apply and then ok the changes won't save and all the filled box get resetThere is no duplicated interfaceDo you know what should I do?Thanks
Hello Good People,When we are browsing WLC C9800 ip via https it is showing not secure. As far i know it needs SSL certificate. I have found some documents in cisco website regarding CSR certificate and Self Sign certificate. In this case, which can ...
Helloi want it is correct that FlexConnect mode does not support centralized authentication only local authentication ? i wait a reply from expert wifi ?Thanks
