I am having issues with WCS (4.0.66.0) not emailing out critical events. I have a vaild smtp server and email addresses. When running a packet analyzer I do not see communication even trying to start to the smtp server.The server has been rebooted.
I am having issues with WCS (4.0.66.0) not emailing out critical events. I have a vaild smtp server and email addresses. When running a packet analyzer I do not see communication even trying to start to the smtp server.The server has been rebooted.
Hei Everybody. Does anybody know if there is a SNMP mib sfor reading/setting RF channel and other RF-parameters on 1131AG standalone Accesspoints. In my network we are using the "least congested frequency" choice for Channel selection and wants t...
Dear List,I was wondering if there is an error on the Cisco documentation below.The diagram and config shows the LWAPs attached to the switch on vlan 5, but the trunk to the WLC is pruning vlan 5.If this is correct, how can the LWAPs speak LWAPP with...
Dear All, i have the following problem ...we have printers on local network 192.168.100.XXX ....<-- DHCP is disablesour Cisco Wirless LAN Controller is on different network 192.168.105.XXX .... <-- DHCP enabledthe wirless device is connected to the l...
Is there a third party omni antenna that is more powerful then the cisco 9bi antenna (AIR-ANT58G9VOA-N ) that I can purchase?ThanksJustin
I have Cisco AIR-LAP1131G-E-K9 but now I want to convert it to Autonomous. I am trying the method of IOS upgradation the way mention on the forum and cisco site but I am not able to do that.process_config_recovery: set IP address and config to defaul...
I am trying to manage a Cisco 4402 using non-default snmp communities from Cisco Works RME 4.0. RME Credential Verification fails with “Device Not Supported” recorded against selected option; however, the controller does respond to snmp queries. Th...
Hi. I have a WLC controller with webauth athentication using an external RADIUS for authentication and accounting. Everything is working fine, except that the accounting updates only happen at session start or stop, and sometimes (!?) there are int...
The 1131 Access point in IOS mode had an option to turn off the BLUE LED circle on the access point. The access point has been converted to LWAP and connected to controller and now the BLUE LED circle is back.... is there any way to turn it off ??C...
Which Cisco Works is compatible with Wireless LAN Controller, for example 4400 series?
Hello,I purchased the following devices as part of the Cisco Mobility Express Solution:2 x Cisco 520 Series Wireless LAN Controller2 x Cisco Catalyst Express 520 Series Switch8 x Cisco 521 Series Access Point ( AIR-LAP521G-E-K9).1 x Cisco RV042 Route...
Hi, Having successfully connected the handset to our system. We came in this morning to play a play a little more. The trouble is the phone will not connect to any network. It just sits there saying "Acquiring Network". I have checked the usual stuff...
Hi,Can someone help me for configuring N-Series band on Cisco 1252 Access Point in IOS Mode.ThanksTabrez
I bought a group of 10 Aironet 1232AGs, and after I enter enable mode cannot enter configuration mode using config t. I think the reason why was because they may have previously been controlled by a WLC. Is there anyway to sort of "reset" them so tha...
why do we need radio interfaces in AP. what is the purpose of creating sub interfaces.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-17-2024 01:03 PM | ||
05-17-2024 12:21 AM | ||
05-14-2024 05:09 PM | ||
05-08-2024 11:10 AM | ||
04-12-2024 05:27 AM |
User | Count |
---|---|
13 | |
12 | |
6 | |
6 | |
4 |