Hi i have few questions regarding stacks Q1 how many 9500 or 9400 i can stack together? all document i have seen all about 2 switches only, can i do more?Q2 while connect stacking cables for 9300 how to make it in the right order like master will be ...
Forum Posts
Hi!I just updated the firmware on our Catalyst 16-port switch (model# WS-C2960L-16TS-LL) using the Web UI to version 15.2(7)E3. The upload and install appeared to be successful. The uploaded file was of type "Universal with Web Based Dev Mgr" (.tar f...
Hello. I'm student. I found trouble on switch2(f0/2 and f0/3) after checked with#show interface f0/2 is FastEthernet0/2 is down, line protocol is down (disabled)Hardware is Lance, address is 000a.f379.7702 (bia 000a.f379.7702)BW 100000 Kbit, DLY 1000...
Trying to reinstall my Anyconnect 4.9.04043, but even though all the boxes were checked, I kept getting failed installation errors. See attached files.
Resolved! Ping is working with bad gateway
Hey guys, I have the following topology: The two networks addresses are 192.168.1.0/24 and 192.168.2.0/24. The gateways for the networks are 192.168.1.1/24 and 192.162.2.1/24 respectively.The strange thing that popped up was that if I add a totally w...
hi all i need to know how to upgrade my ios router and he u are the following show version : Router#show versionCisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.4(3)M1, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com...
Hello community,I need your help. I changed a switch today (old: C3560, new: C2960X). The old C3560 was connected to another C3560 over a trunk port.Since I changed the switch (same config, same vlans etc.) the C3560 on the other side remains root b...
Resolved! Catalyst 9300 and extended VLANs
If I'm currently running VTP version 1 or 2 on my network and I have a 9300 switch in Client mode, I change to Server mode and create an extended VLAN, then go back to Client mode, will the revision number increment? I can't confirm but I don't belie...
Hello Cisco Community, I'm hoping you can assist me...Don't know what happen, buy my post disappeared. I have a IR 829 router that can ping the internetGLE-CE-02#ping 8.8.8.8 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 8.8.8.8, t...
Hey forums, so I have a situationI used to be able to SSH connect from my Catalyst to my Nexus, doing like a nested SSH situationAfter I updated the Nexus to the version 8.4.2, when I attempt to access the Nexus, it closes my Catalyst SSH sessionI am...
Resolved! Can i do stack switch with StackWise cable after switch on production with different configuration ?
Dear AllI would like to ask about Stack cisco 9200 with StackWise cable.if I install switch 9200 on production 2 unit with different configuration if i would lilke to so stack both switchMy question before i connect stackwise i should factory conf...
Resolved! Advice on switch.
Hi, consider my devices and suggest networking.cluster1:intel nuc1 : no internet, or any other connections. Only connects to intel nuc2 on specific ports.Would like to have flexibility in managing/assigning ports, ip to which its allowed toconnectint...
Hi Guys I´m new here, and I´m studying of CCNA in the Dominican Republic.How can I disable systema message or alerts of a router or switch???Example:if i type: no shutdown in a interface display the following message or alert%LINK-5-CHANGED: Interfac...
Hi all, I would like to get assistance to understand on what is the means for "sdwan-20.4(1.79)" under the known fixed release in bug ID/caveats (https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvw93086). When checking in the software release, I can ...
Hello there,I'm new to this topic and I'm searching for the last days for a solution and before buying a router I wanted to make sure that my understanding is correct. Task:I have x-amounts of customer devices which all have the same hard coded IP an...
