Activity in DevNet Site
FMC API Move rule to another category/section
Hello! I am trying to move a rule to a category/section via the API, but I'm not sure how to do it via the PUT endpoint. I have tried this:PUT with partialUpdate=True with following payload:{"metadata": {"category":"test_category"}, "id":rule_id}Resp...
Default login and password admin not working on xpresso login page
I just finished installing the docker container complete with xpresso. I opened my browser (firefox) to the gui and it came up with the login page. However, when I tried using the default login of admin/admin I get wrong password.Any suggestions?Than...
Meraki Always On Lab OTP verification
I am attempting to Launch the Meraki Always On Lab. In the launch instructions there is this message in regards to OTP.Meraki has enhanced security features which will ask OTP verification for new IP login since Dec. 2022. Please refer Authenticatio...
Reserve sandbox
Hello,How do you actually reserve a sandbox? There doesn't seem to be any Reserve button any more on this latest GUI. I'm logging in and looking at this site: https://devnetsandbox.cisco.com/DevNet Thanks!
Resolved! CML Sandbox Availability
have tried to launch the CML Sandbox from https://devnetsandbox.cisco.com/DevNet a few times today and each time it was at its capacity. Is there a particular time of day / day of the week where it is more likely to be available?
Active environments launched from this blueprint reached
Trying to run Cisco modeling lab. Get Limit for active environments launched from this blueprint reached. Please try later.
Devnet Meraki Always On login issue
Please explain why to provide not accessible resource.According to documentation, user may access Meraki always on with following creds-DevNet Always On Read OnlyUsing the following credentials:Username: devnetmeraki@cisco.comPassword: Adm!n123!They ...
Sandbox down, any eta?
Since about this time yesterday all of the sandboxes are down. Is there any eta when the devnet sandboxes will be back up?
Resolved! Zombie Environment: "Terminate failed"
Hi,My most recent CML environment is in a zombie state and it can't be extended or ended. No new environments can be launched. How, if at all possible from my end, can i clear it?
Resolved! Always On IOSXE Sandbox Password Reset
The standard admin password for "IOS XE on Cat8kv AlwaysOn" (devnetsandboxiosxe.cisco.com) is not working. Can this environment please be reset to defaults?
Unable to claim target in EU region
Hi.When I'm trying to claim a new target from my Sandbox in Intersight I get the message:"The device has not been updated to support claim in this region. Please wait for device to be upgraded, if issue persists please contact Cisco TAC.". How can I ...
REST API POST action permission issue
Getting an error message while running POST action. Role does not have valid permissions to access the API
How to End a Sandbox Reservation (and Reserve a New One)
Hello fellow DevNet Sandbox Surfers! To see the status of your active and past reservations, navigate to the ‘Environments’ page by clicking on the ‘Environments’ tab on the left side of the main sandbox ‘Catalog’ page (https://devnetsandbox.cis...
Resolved! AnyConnect Connection Failure - Cloud-Native SD-WAN Lab
Trying to access the Cloud-Native SD-WAN Lab in the Devnet Sandbox using Anyconnect. Receiving the following logs and error.[4/29/2024 3:21:17 PM] Ready to connect.[4/29/2024 3:21:35 PM] Contacting devnetsandbox-usw1-reservation.cisco.com:20294.[4/29...
Firepower Management Center lab: how to connect to eStreamer service
Hi!I started a Firepower Management Center sandbox with the hope of testing a eStreamer client application. But as far as I see there is only the HTTP UI/api available, and without an option to setup a VPN it is not possible to connect on other ports...
| User | Helpful Count |
|---|---|
| 11 | |
| 6 | |
| 2 | |
| 2 | |
| 1 |
